Yeticom Optima 10/12 Meter Mobile EXPORT Transceiver

24.500-29.999 Mhz  coverage

Out of stock till late December 2011 sorry

completely new to the market and exclusive to yeti communications read notes below

GENERAL SPECIFICATIONS
Frequency Coverage: 24.500 to 29.999 Mhz
Antenna Impedance: 50 ohm, unbalanced
Frequency Control: Digital Phase-Lock Loop (PLL) Synthesizer
Frequency Accuracy: Better than +10 ppm from 0 - 40 °C after 15 min. warm up
Power Requirement: 12 -13.8 V DC, negative ground
Current Consumption: 9 amps maximum
Dimensions: 6 x 2 x 9.5 in (W x H x D)
Weight: 2.9 Ibs

TRANSMITTER SPECIFICATIONS
Power Output: SSB/ FM...50 Watts+, ...AM..15 Watts RMS / 50 Watts PEP
Tuning Steps: 1 kHz /5Khz/10 kHz /100 kHz/1Mhz   5khz default step
Final Transistors: IRF520 MOSFET (x2)
Spurious Emissions: More than 50 dB below peak output power
Carrier Suppression: More than 40 dB below peak output power
Unwanted Sideband: More than 50 dB below peak output (1 kHz tone)
FM Deviation: +/- 5 kHz maximum
Audio Response: More than 30dB below peak output
Frequency Response: 400 to 2800 Hz
Microphone Impedance: ECM, 600 to 1 K ohms

RECEIVER SPECIFICATIONS
Circuit Type: Dual-Conversion Super-heterodyne
Intermediate Frequencies:
1st IF/SSB IF...10.695 MHz
2nd IF...455 kHz
Sensitivity:
SSB...0.25 V at 10 dB S + N/N
AM...1.0 V at10dBS+N/N
FM...0.3 V at12dBSINAD
Selectivity:
SSB...4.2 kHz (-6 dB) / 8.5 kHz (-60 dB)
AM / FM...6.0 kHz (-6 dB) /18 kHz (-60 dB)
Clarifier Range: +/-1.5 kHz
Adjacent Channel Rejection: Better than 70 dB
I F Rejection: Better than 85 dB for all frequencies
Frequency Response: 250 to 3000 Hz
Audio Output Power: 2 watts minimum at 10% THD with an 8 ohm load
Audio Output Impedance: 8 ohms 
RF Power Output 50W SSB (pep)/ 15W AM (rms)/ 50W FM (rms)                       
Dual Finals on Heat Sink with temp controlled fan
Modes AM, FM, USB, LSB
Microprocessor Controlled
5 memories
Last Channel Recall
Frequency Scan in any step (1khz/5khz/10khz/100khz)
Variable RF Output Power all modes
Variable Mic Gain
Repeater offset...1khz-999khz +/- offset all bands all modes
5 Digit LCD Frequency Display
Scanning Microphone step in 1/5/10/100khz steps
Night Illuminated Display white led
Surface Mount Technology throughout
Dimensions 2(H) x 6(W) x 9.5(D) in

New and exclusive to yeticomnz.com is the yeticom optima. Fully redesigned and improved on  with new coverage ..cooling...steps....filter stages...rf final stage shielding...designed by New Zealanders and made in China to meet the demands of the modern day ham radio operator .

Firstly the frequency coverage. This is available in four different configurations:

1:: New Zealand   40 cb radio channels only. No spilt offset   26.330-26.770 inclusive  channel or freq display

2::USA/Australian   40 cb radio channels only. No spilt offset    26.965-27.405 inclusive  channel or freq display

3:: 12 meter and 10 meter bands only (24.500-25.000/28.000-29.999 split available  frequency display only (default coverage)

4:: 24.500-29.999 split available  frequency display only (export mode)

Full use of the repeater spilt function is available on all bands (12/10meter or export modes only) at any time  unlike pervious versions.

We have added a extra frequency tuning step  the radio now defaults to 5khz stepping on power up to move around the bands faster of course  stepping in 1/5/10/100khz steps can still be changed at any time. also we have redesigned the software so stepping  has flow stepping just like the more expensive rigs...no more need of going back into the "function/call" to step up into the next band. like we said no gaps no jumps.

The transceiver has extra shielding in the rf driver/final stages added to comply with international regulations and type approval

Fm mode now has per and de-emphasis in the audio chain for far better fm mode operation for the European market

The receive has a new design to remove imaging problems pervious models had. Also we had had the manufactor improve the if filter and if filter stages for lower if noise ..another thing pervious models suffered from.

Extra cooling has been provided for the hotter climates ..the cooling is provided by a temperature controlled fan on the heat sink.

The mother board is a completey new design  .

Mic wiring early and late Yeticom Optima

What's in this package?
- Mobile bracket with screws
- Microphone
- DC cable
- Replacement fuse
Certificate CE,ROHS
Warranty:
90 day standard yeti communications R.T.B warranty concurrent with the1 year factory standard warranty.

Manufactor: Good Will Telecom China for Yeticomnz.com

OPTIMA OPERATING MANUAL DOWNLOAD

This site is © Copyright www.survival-systems.com 2005-2011, All Rights Reserved.